Single-Action Hydraulic Cylinder for scissor lifts 250 bar // series: HZE3
General information
The HZE1 series cylinders are single-action pressure cylinders that are universally applicable due to their various models and sealing variants. The piston rod guide is designed to be screwable for maintenance tasks. The piston rod consists of hightensile structural steel with an approximately 25µm hard chromium-plated layer. Other materials and coatings are available on request. The end of the piston rod is guided into the cylinder tube, which minimizes the wear of the piston rod guide and the seal.
Please consult us in case of radial forces and non-vertical installation.
Technical data | |
---|---|
Max. operating pressure | = 250 bar |
Test pressure | = 315 bar |
Rod ∅ | = 50 – 130mm |
Temperature range | = -20°C to +80°C |
Pressure fluid | = Mineral oil (HL, HLP) according to DIN 51524 and DIN 51525 (standard) |
Stroke speed | = ≤ 0,5 m/s |
Length and stroke tolerances according to DIN7168g (see “Technical Information“)
Baureihen | ||
---|---|---|
Bodenseitiges Gelenklager | (DO – Standard) | HZE ≤ 500 mm Hub |
Bodenseitiges Gelenklager | (DO – Standard) | HZE > 500 mm Hub |
Bodenseitiges Gelenklager | (DO – Standard) | HZE > 1000 mm Hub |
Weitere produktspezifische Informationen
Bestellschlüssel Klicken Sie hier um den Bestellschlüssel im PDF-Format herunterzuladen.
Anschlussbohrungen
Die Anschlussbohrung in Rohrgewinde nach ISO 228/1 befindet sich am bodenseitigen Ende des Zylinders und kann auch für Leitungsbruch- und Senkbremsventile ausgeführt werden, wobei sich die Höhe des Anschlussstutzen ändert.
Die Lage auf dem Umfang kann geändert werden (Standard P8).
Anschlussgewinde | Leitungsbruchsicherung | Senkbremsventil | ||
---|---|---|---|---|
Höhe | Gewindetiefe | Höhe | Gewindetiefe | |
G1/4″ | 40 | 32 | 55 | 32 |
G3/8″ | 50 | 35 | 60 | 34 |
G1/2″ | 55 | 44 | 70 | 40 |
G3/4″ | 65 | 51 | 80 | 51 |

D1 – Nutring und Abstreifer aus Polyurethan (Standard) | |
---|---|
Temperatur | -30°C bis +80°C |
Druckflüssigkeit | Mineralöl |
Hubgeschwindigkeit | ≤ 0,5 m/s |
Anwendung | Standarddichtsatz für normale Betriebsbedingungen, sehr hoher Verschleißwiederstand |
D2-Gleitringdichtsatz besteht aus PTFE-STEP-SEALS (NBR – O-Ring) | |
---|---|
Temperatur | -30°C bis +100°C |
Druckflüssigkeit | Mineralöl, schwer entflammbare Druckflüssigkeiten HFA und HFB bis +40°C; HFC bis +60°C |
Hubgeschwindigkeit | ≤ 1 m/s |
Anwendung | Dichtsatz für hohe Gleitgeschwindigkeiten, kein Stick-Slip-Effekt, höhere Leckagen als bei D1 und D3 |
D2V-Gleitringdichtsatz besteht aus PTFE-STEP-SEALS (Viton – O-Ring) Doppelabstreifer (Viton – O-Ring) | |
---|---|
Anwendung | Dichtsatz für hohe Gleitgeschwindigkeiten, kein Stick-Slip-Effekt, höhere Leckagen als bei D1 und D3, für höhere Temperaturen (+200°C) und Flüssigkeiten auf Phosphatesterbasis (HFD) |
D3 – Tandemdichtsatz besteht aus Nutring (Polyurethan) und PFTE-STEP-SEAL | |
---|---|
Temperatur | -30°C bis +80°C |
Druckflüssigkeit | Mineralöl |
Hubgeschwindigkeit | ≤ 0,8 m/s |
Anwendung | Dichtsatz für hohe Belastungen und minimalen Leckagen, leichtgängige Hubbewegungen |
Theoretische Zylinderkraft in [kN] (Wirkungsgrad = 100%)
Stangen Ø [mm] | Druckfläche [mm²] | Betriebsdruck in [bar] | ||||
---|---|---|---|---|---|---|
50 | 100 | 150 | 200 | 250 | ||
50 | 1963,5 | 9,8 | 19,6 | 26,5 | 39,3 | 49,1 |
60 | 2827,4 | 14,1 | 28,3 | 42,4 | 56,5 | 70,7 |
70 | 3848,5 | 19,2 | 38,5 | 57,7 | 77,0 | 96,2 |
80 | 5026,5 | 25,1 | 50,3 | 75,4 | 100,5 | 125,7 |
90 | 6361,7 | 31,8 | 63,6 | 95,4 | 127,2 | 159,0 |
100 | 7854,0 | 39,3 | 78,5 | 117,8 | 157,1 | 196,3 |
110 | 9503,3 | 47,5 | 95,0 | 142,5 | 190,1 | 237,6 |
120 | 11309,7 | 56,5 | 113,1 | 169,6 | 226,2 | 282,7 |
130 | 13273,2 | 66,4 | 132,7 | 199,1 | 265,5 | 331,8 |